AT28LV010
3. Block Diagram
4. Device Operation
4.1
4.2
Read
Write
The AT28LV010 is accessed like a Static RAM. When CE and OE are low and WE is high, the
data stored at the memory location determined by the address pins is asserted on the outputs.
The outputs are put in the high impedance state when either CE or OE is high. This dual-line
control gives designers flexibility in preventing bus contention in their system.
The write operation of the AT28LV010 allows 1 to 128 bytes of data to be written into the
device during a single internal programming period. Each write operation must be preceded by
the software data protection (SDP) command sequence. This sequence is a series of three
unique write command operations that enable the internal write circuitry. The command
sequence and the data to be written must conform to the software protected write cycle timing.
Addresses are latched on the falling edge of WE or CE, whichever occurs last and data is
latched on the rising edge of WE or CE, whichever occurs first. Each successive byte must be
written within 150 μs (t BLC ) of the previous byte. If the t BLC limit is exceeded the AT28LV010
will cease accepting data and commence the internal programming operation. If more than
one data byte is to be written during a single programming operation, they must reside on the
same page as defined by the state of the A7 - A16 inputs. For each WE high to low transition
during the page write operation, A7 - A16 must be the same.
The A0 to A6 inputs are used to specify which bytes within the page are to be written. The
bytes may be loaded in any order and may be altered within the same load period. Only bytes
which are specified for writing will be written; unnecessary cycling of other bytes within the
page does not occur.
3
0395F–PEEPR–08/09
相关PDF资料
AT32UC3C-EK KIT EVAL AVR32 UC3 MCU IND AUTO
AT34C02B-10TU-1.7 IC EEPROM 2KBIT 400KHZ 8TSSOP
AT34C02C-TH-T IC EEPROM 2KBIT 400KHZ 8TSSOP
AT45CS1282-TC IC FLASH 128MBIT 50MHZ 40TSOP
AT45DB011B-XI IC FLASH 1MBIT 20MHZ 14TSSOP
AT45DB021B-TI IC FLASH 2MBIT 20MHZ 28TSOP
AT45DB041B-TI IC FLASH 4MBIT 20MHZ 28TSOP
AT45DB081B-TI IC FLASH 8MBIT 20MHZ 28TSOP
相关代理商/技术参数
AT28LV010-20JU SL319 制造商:Atmel Corporation 功能描述:PARALLEL EEPROM, 1M (128K X 8), 3V, SDP - 200NS, PLCC, IND T - Tape and Reel
AT28LV010-20JU SL383 制造商:Atmel Corporation 功能描述:EEPROM Parallel 1M-bit 128K x 8 3.3V 32-Pin PLCC T/R 制造商:Atmel Corporation 功能描述:EEPROM PARALLEL 1MBIT 128KX8 3.3V 32PLCC - Tape and Reel 制造商:Atmel 功能描述:EEPROM Parallel 1M-bit 128K x 8 3.3V 32-Pin PLCC T/R
AT28LV010-20JU-051 功能描述:IC EEPROM 1MBIT 200NS 32PLCC 制造商:microchip technology 系列:- 包装:管件 零件状态:在售 存储器类型:非易失 存储器格式:EEPROM 技术:EEPROM 存储容量:1Mb (128K x 8) 写周期时间 - 字,页:10ms 访问时间:200ns 存储器接口:并联 电压 - 电源:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C(TC) 安装类型:表面贴装 封装/外壳:32-LCC(J 形引线) 供应商器件封装:32-PLCC 标准包装:32
AT28LV010-20JU-235 功能描述:IC EEPROM 1MBIT 200NS 32PLCC 制造商:microchip technology 系列:- 包装:剪切带(CT) 零件状态:在售 存储器类型:非易失 存储器格式:EEPROM 技术:EEPROM 存储容量:1Mb (128K x 8) 写周期时间 - 字,页:10ms 访问时间:200ns 存储器接口:并联 电压 - 电源:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C(TC) 安装类型:表面贴装 封装/外壳:32-LCC(J 形引线) 供应商器件封装:32-PLCC 标准包装:1
AT28LV010-20JU-319 功能描述:IC EEPROM 1MBIT 200NS 32PLCC 制造商:microchip technology 系列:- 包装:管件 零件状态:在售 存储器类型:非易失 存储器格式:EEPROM 技术:EEPROM 存储容量:1Mb (128K x 8) 写周期时间 - 字,页:10ms 访问时间:200ns 存储器接口:并联 电压 - 电源:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C(TC) 安装类型:表面贴装 封装/外壳:32-LCC(J 形引线) 供应商器件封装:32-PLCC 标准包装:32
AT28LV010-20JU-630 功能描述:IC EEPROM 1MBIT 200NS 32PLCC 制造商:microchip technology 系列:- 包装:管件 零件状态:在售 存储器类型:非易失 存储器格式:EEPROM 技术:EEPROM 存储容量:1Mb (128K x 8) 写周期时间 - 字,页:10ms 访问时间:200ns 存储器接口:并联 电压 - 电源:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C(TC) 安装类型:表面贴装 封装/外壳:32-LCC(J 形引线) 供应商器件封装:32-PLCC 标准包装:750
AT28LV010-20JU-T 功能描述:IC EEPROM 1MBIT 200NS 32PLCC 制造商:microchip technology 系列:- 包装:剪切带(CT) 零件状态:在售 存储器类型:非易失 存储器格式:EEPROM 技术:EEPROM 存储容量:1Mb (128K x 8) 写周期时间 - 字,页:10ms 访问时间:200ns 存储器接口:并联 电压 - 电源:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C(TC) 安装类型:表面贴装 封装/外壳:32-LCC(J 形引线) 供应商器件封装:32-PLCC(11.43x13.97) 标准包装:1
AT28LV010-20PC 功能描述:电可擦除可编程只读存储器 1M 3V SDP- 200NS COM TEMP RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8